Mack M123 tractor truck and M125 truck

M123 Tractor Truck and M125 Cargo Truck

Mack M123 Tractor Truck
Type 10‑ton 6x6 trucks
Place of origin United States
Production history
Designer Mack
Manufacturer Mack, CONDEC
Produced 1955–1969
Number built 3580 (+552 M125)
Specifications (M123[1])
Weight 32,490 lb (14,740 kg) empty
Length 23 feet 4 inches (7.11 m)
Width 9 feet 6 inches (2.90 m)
Height 9 feet 3 inches (2.82 m)
Engine Le Roi TH-844
(for other see text)
297 hp (221 kW)
Transmission 5 speed x 2 range
Suspension Beam axles on leaf springs
Operational
range
 300 mi (482.8 km)
Speed 42 mph (68 km/h)

The Mack M123 (G792) was a 10-ton (9,072 kg) 6x6 gasoline-powered semi-tractor introduced in 1955; the Mack M125 was a heavy cargo truck version of the M123. The M123 was used to tow tank transporter trailers while the M125 towed field artillery pieces.

History

In 1949 the US Army set a requirement for a family of 10‑ton (9,072 kg) load rated extra heavy-duty tactical trucks. Mack’s design, influenced by their WWII era NO, was chosen. Designed as an entire family, only the semi-tractor and cargo/prime mover were built. 392 M123s were built between 1955 and 1957 and 552 M125s in 1957 and 1958.

In 1965 CONDEC began building 3188 diesel powered M123As, Mack began building 420 in 1968. In 1969 Mack then upgraded 210 gas engine models to diesel power.

With the Army using more self‑propelled artillery, the need for prime movers was reduced, no follow‑up orders for M125s were made.

Both M123s and M125s saw service in the Vietnam War. M123 tractors remained in Army service into the 1990s.

In addition to the US Army, the M123 was used by the U.S. Marine Corps and exported to U.S. allies in such countries as Australia and Spain.[2][3][4]

Specifications

Engine and driveline

All M123s and M125 built in the 1950s had a LeRoi T‑H844 engine, a 844 cu in (13.8 L) overhead valve V 8 gasoline engine developing 297 hp (221 kW) at 2600 rpm and 725 lbf·ft (983 N·m) of torque at 1700 rpm. M123A1s built in the 1960s had a Cummins V8‑300, a 785 cu in (12.9 L) naturally aspirated V 8 diesel engine developing 300 hp (220 kW) at 3000 rpm and 580 lbf·ft (786 N·m) torque at 2100 rpm. This engine was also retrofitted into M123s to make M123E2s. No M125s were converted to diesel power.[1][3][5][6]

The drivetrain was a repeat of that in the Mack NO, with a Mack TRDXT72 5 speed transmission with the transfer case mounted solidly to the rear of the transmission. This transmission was direct in 5th. The transfer case had a 2.50:1 low range, engaged the front axle, and had a power take-off to operate the winch(s).[3][7][8][9]

The front axle was an unusual triple reduction type which did not need u‑joints on the outer ends and allowed a tighter turning radius. The two rear axles were a double reduction type. Final drive ratios were 9.02:1 for gas powered trucks and 10.11:1 for diesels. All drivelines of both manufacturers were built by Mack.[4][5][10][11]

Chassis

A ladder frame was used. The front beam axle was mounted on leaf springs, the rear tandem beam axles were mounted on a leaf sprung “walking beam” type suspension. All models shared a 181 inches (4.60 m) wheelbase (measured from 1st to 3rd axles). Full air drum brakes were used, M123s were able to control the trailer brakes independently of the tractor. M125s had electrical connections for the artillery piece brakes. Tire size was 14.00x24.[5][7][11]

The main differences between various chassis was the location of the 45,000 lb (20,000 kg) winches and fifth-wheels. Different M123 models had either one or two winches mounted behind the cab, all M125s had a single winch at the front.[1]

The M15A2 trailer the M123 was first intended to tow had a higher load plate and larger coupling pin than a standard semi-trailer. Early M123s had a larger fifth wheel mounted above the frame rails, but as more standard trailers were used the M123C and all following models had lowered fifth wheels. The pin remained larger, so any trailer towed by any M123 had to have an interchangeable pin.[3]

A standardized REO designed cab, also used in  2 1⁄2 and 5‑ton trucks, was used. It had hinged doors with roll-up windows, a folding windshield, and a removable canvas roof. A hard roof could be fitted. With the same cabs and similar design fenders and hoods, the main visual difference between these three sizes was the size of the vehicle and the scale of the cab to the vehicle.[2][3]

Models

M123

The M123 was used to tow semi-trailers carrying MBT's (in conjunction with the M15A1 and later the M747 semi-trailer) and as such superseded the M26(A1) Pacific "Dragon Wagon" and semi-trailers carrying engineering equipment (e.g. in conjunction with the M 127 low bed semi-trailer).

Variants:

M125

The M125 succeeded the Mack NO as a heavy cargo transport vehicle; it also served as a prime mover towing the 155‑mm gun and 8‑in. howitzer. The chassis was designated M121. It had a 14 ft (4.27 m) steel cargo body with folding troop seats, bows and canvas cover. A single front-mounted Gar Wood DSA716 45,000 lb (20,000 kg) capacity winch was fitted, and a chain hoist at rear for handling ammunition.[4]

See also

Wikimedia Commons has media related to Mack M123 tractor truck and M125 truck.

Notes

References

This article is issued from Wikipedia - version of the 11/21/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.