Nagle's algorithm

Nagle's algorithm is a means of improving the efficiency of TCP/IP networks by reducing the number of packets that need to be sent over the network. It was defined by John Nagle while working for Ford Aerospace and Communications Corporation.

Nagle's document, Congestion Control in IP/TCP Internetworks (RFC 896) describes what he called the "small packet problem", where an application repeatedly emits data in small chunks, frequently only 1 byte in size. Since TCP packets have a 40 byte header (20 bytes for TCP, 20 bytes for IPv4), this results in a 41 byte packet for 1 byte of useful information, a huge overhead. This situation often occurs in Telnet sessions, where most keypresses generate a single byte of data that is transmitted immediately. Worse, over slow links, many such packets can be in transit at the same time, potentially leading to congestion collapse.

Nagle's algorithm works by combining a number of small outgoing messages, and sending them all at once. Specifically, as long as there is a sent packet for which the sender has received no acknowledgment, the sender should keep buffering its output until it has a full packet's worth of output, so that output can be sent all at once.

Algorithm

if there is new data to send
  if the window size >= MSS and available data is >= MSS
    send complete MSS segment now
  else
    if there is unconfirmed data still in the pipe
      enqueue data in the buffer until an acknowledge is received
    else
      send data immediately
    end if
  end if
end if

where MSS = maximum segment size

This algorithm interacts badly with TCP delayed acknowledgments, a feature introduced into TCP at roughly the same time in the early 1980s, but by a different group. With both algorithms enabled, applications that do two successive writes to a TCP connection, followed by a read that will not be fulfilled until after the data from the second write has reached the destination, experience a constant delay of up to 500 milliseconds, the "ACK delay". For this reason, TCP implementations usually provide applications with an interface to disable the Nagle algorithm. This is typically called the TCP_NODELAY option.

A solution recommended by Nagle is to avoid the algorithm sending premature packets by buffering up application writes and then flushing the buffer:

The user-level solution is to avoid write-write-read sequences on sockets. write-read-write-read is fine. write-write-write is fine. But write-write-read is a killer. So, if you can, buffer up your little writes to TCP and send them all at once. Using the standard UNIX I/O package and flushing write before each read usually works.[1]

Negative effect on larger writes

The algorithm applies to data of any size. If the data in a single write spans 2n packets, the last packet will be withheld, waiting for the ACK for the previous packet.[2] In any request-response application protocols where request data can be larger than a packet, this can artificially impose a few hundred milliseconds latency between the requester and the responder, even if the requester has properly buffered the request data. Nagle's algorithm should be disabled by the requester in this case. If the response data can be larger than a packet, the responder should also disable Nagle's algorithm so the requester can promptly receive the whole response.

In general, since Nagle's algorithm is only a defense against careless applications, it will not benefit a carefully written application that takes proper care of buffering; the algorithm has either no effect, or negative effect on the application.

Interactions with real-time systems

Applications that expect real time responses can react poorly with Nagle's algorithm. Applications such as networked multiplayer video games expect that actions in the game are sent immediately, while the algorithm purposefully delays transmission, increasing bandwidth efficiency at the expense of latency. For this reason applications with low-bandwidth time-sensitive transmissions typically use TCP_NODELAY to bypass the Nagle delay.[3]

Another option is to use UDP instead.

References

  1. ↑ John Nagle (January 19, 2006), Boosting Socket Performance on Linux, Slashdot
  2. ↑ "TCP Performance problems caused by interaction between Nagle's Algorithm and Delayed ACK". Stuartcheshire.org. Retrieved November 14, 2012.
  3. ↑ Bug 17868 – Some Java applications are slow on remote X connections

External links

This article is issued from Wikipedia - version of the 10/31/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.