POWER4

POWER4
Produced 2001
Designed by IBM
Max. CPU clock rate 1.1 GHz to 1.9 GHz
Min. feature size 180 nm to 130 nm
Instruction set PowerPC (PowerPC v.2.00/01)
Cores 2
L1 cache 64+32 kB/core
L2 cache 1.41 MB/chip
L3 cache 32 MB off chip
Predecessor POWER3, RS64
Successor POWER5

The POWER4 is a microprocessor developed by International Business Machines (IBM) that implemented the 64-bit PowerPC and PowerPC AS instruction set architectures. Released in 2001, the POWER4 succeeded the POWER3 and RS64 microprocessors, and was used in RS/6000 and AS/400 computers, ending a separate development of PowerPC microprocessors for the AS/400. The POWER4 was a multicore microprocessor, with two cores on a single die, the first non-embedded microprocessor to do so.[1] POWER4 Chip was first commercially available multiprocessor chip.[2] The original POWER4 had a clock speed of 1.1 and 1.3 GHz, while an enhanced version, the POWER4+, reached a clock speed of 1.9 GHz. The PowerPC 970 is a derivative of the POWER4.

Functional layout

The logic schema of the POWER4 core
The logic schema of the POWER4 processor

The POWER4 has a unified L2 cache, divided into three equal parts. Each has its own independent L2 controller which can feed 32 bytes of data per cycle. The Core Interface Unit (CIU) connects each L2 controller to either the data cache or instruction cache in either of the two processors. The Non-Cacheable (NC) Unit is responsible for handling instruction serializing functions and performing any noncacheable operations in the storage topology. There is an L3 cache controller, but the actual memory is off-chip. The GX bus controller controls I/O device communications, and there are two 4-byte wide GX buses, one incoming and the other outgoing. The Fabric Controller is the master controller for the network of buses, controlling communications for both L1/L2 controllers, communications between POWER4 chips {4-way, 8-way, 16-way, 32-way} and POWER4 MCM’s. Trace-and-Debug, used for First Failure Data Capture, is provided. There is also a Built In Self Test function (BIST) and Performance Monitoring Unit (PMU). Power-on reset (POR) is supported.

Execution units

The POWER4 implements a superscalar microarchitecture through high-frequency speculative out-of-order execution using eight independent execution units. They are: two floating-point units (FP1-2), two load-store units (LD1-2), two fixed-point units (FX1-2), a branch unit (BR), and a conditional-register unit (CR). These execution units can complete up to eight operations per clock (not including the BR and CR units):

The pipeline stages are:

Multi-chip configuration

The POWER4 also came in a configuration using a multi-chip module (MCM) containing four POWER4 dies in a single package, with up to 128 MB of shared L3 ECC cache per MCM.

Parametrics

POWER4 180 nm@CMOS 8S3 SOI
Clock GHz 1.3 GHz
Power 115 W 1.5 V @ 1.1 GHz
Transistors 174 million
Gate L 90 nm
Gate oxide 2.3 nm
Metal-layer pitch thickness
M1 500 nm 310 nm
M2 630 nm 310 nm
M3-M5 630 nm 420 nm
M6(MQ) 1260 nm 920 nm
M7(LM) 1260 nm 920 nm
Dielectric ~4.2
Vdd 1.6 V

POWER4+

The POWER4+ was an improved version of the POWER4 that ran at up to 1.9 GHz. It contained 184 million transistors, measured 267 mm2, and was fabricated in a 0.13 µm SOI CMOS process with eight layers of copper interconnect.

Notes

  1. ↑ "IBM's Server Processors: The RS64 and the POWER". The CPU Shack Museum. 2011-01-24. Retrieved 2015-04-17.
  2. ↑ William Stallings, Computer Organization and Architecture, Seventh Edition, -pp 44

References

See also

This article is issued from Wikipedia - version of the 6/4/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.