Breakdown voltage

High voltage dielectric breakdown within a block of plexiglas

The breakdown voltage of an insulator is the minimum voltage that causes a portion of an insulator to become electrically conductive.

For diodes, the breakdown voltage is the minimum reverse voltage that makes the diode conduct in reverse. Some devices (such as TRIACs) also have a forward breakdown voltage.

Solids

Breakdown voltage is a characteristic of an insulator that defines the maximum voltage difference that can be applied across the material before the insulator collapses and conducts. In solid insulating materials, this usually creates a weakened path within the material by creating permanent molecular or physical changes by the sudden current. Within rarefied gases found in certain types of lamps, breakdown voltage is also sometimes called the "striking voltage".^[1]

The breakdown voltage of a material is not a definite value because it is a form of failure and there is a statistical probability whether the material will fail at a given voltage. When a value is given it is usually the mean breakdown voltage of a large sample. Another term is also withstand voltage where the probability of failure at a given voltage is so low it is considered, when designing insulation, that the material will not fail at this voltage.

Two different breakdown voltage measurements of a material are the AC and impulse breakdown voltages. The AC voltage is the line frequency of the mains. The impulse breakdown voltage is simulating lightning strikes, and usually uses a 1.2 microsecond rise for the wave to reach 90% amplitude then drops back down to 50% amplitude after 50 microseconds.^[2]

Two technical standards governing performing these tests are ASTM D1816 and ASTM D3300 published by ASTM.^[3]

Gases and vacuum

In standard conditions at atmospheric pressure, air serves as an excellent insulator, requiring the application of a significant voltage of 30 kV/cm before breaking down (e.g., lightning). In partial vacuum, this breakdown potential may decrease to an extent that two uninsulated surfaces with different potentials might induce the electrical breakdown of the surrounding gas. This may damage an apparatus, as breakdown is analogous to a short circuit.

In a gas, the breakdown voltage can be determined by Paschen's Law.

The breakdown voltage in a partial vacuum is represented as^[4][5][6]

${\displaystyle V_{\mathrm {b} }={\frac {Bpd}{\ln Apd-\ln \left[\ln \left(1+{\frac {1}{\gamma _{\mathrm {se} }}}\right)\right]}}}$

where $V_{{\mathrm {b}}}$ is the breakdown potential in volts DC, $A$ and $B$ are constants that depend on the surrounding gas, $p$ represents the pressure of the surrounding gas, $d$ represents the distance in centimetres between the electrodes, and $\gamma _{{\mathrm {se}}}$ represents the Secondary Electron Emission Coefficient.

A detailed derivation and some background information is given in the article about Paschen's law.

Diodes and other semiconductors

Diode I-V diagram

Breakdown voltage is a parameter of a diode that defines the largest reverse voltage that can be applied without causing an exponential increase in the current in the diode. As long as the current is limited, exceeding the breakdown voltage of a diode does no harm to the diode. In fact, Zener diodes are essentially just heavily doped normal diodes that exploit the breakdown voltage of a diode to provide regulation of voltage levels.

References

1. J. M. Meek and J. D. Craggs, Electrical Breakdown of Gases, John Wiley & Sons, Chichester, 1978.
2. Emelyanov, A.A., Izv. Vyssh. Uchebn. Zaved., Fiz., 1989, no. 4, p. 103.
3. Kalyatskii, I.I., Kassirov, G.M., and Smirnov, G.V., Prib. Tekh. Eksp., 1974, no. 4, p. 84.
4. G. Cuttone, C. Marchetta, L. Torrisi, G. Della Mea, A. Quaranta, V. Rigato and S. Zandolin, Surface Treatment of HV Electrodes for Superconducting Cyclotron Beam Extraction, IEEE. Trans. DEI, Vol. 4, pp. 218<223, 1997.
5. H. Moscicka-Grzesiak, H. Gruszka and M. Stroinski, ‘‘Influence of Electrode Curvature on Predischarge Phenomena and Electric Strength at 50 Hz of a Vacuum
6. R. V. Latham, High Voltage Vacuum Insulation: Basic concepts and technological practice, Academic Press, London, 1995.

See also

• Dielectric strength
• Electrical breakdown
• Avalanche breakdown
• Avalanche diode
• Paschen's law - variation of Breakdown voltage of gas related to pressure
• Electrical treeing
• Lichtenberg figure