Suzuki GT550

The Suzuki GT550 is a two-stroke, air-cooled, three cylinder 1970s-era motorcycle in Suzuki's "Grand Touring" GT series. Even though total production of the 550 exceeded 60,000 examples spread over a six model year production run, this total was exceeded by both of its three-cylinder GT series brothers. Suzuki produced over 80,000 units of the GT750 and over 100,000 units of the GT380. All three models were originally offered for sale with the beginning of the 1972 model year (MY) with the 550 called "Indy" for the North American market.[1] Production of the 550 was delayed because it was not available to dealers in the US until after April, 1972. In Suzuki's numbering scheme, automobile race tracks identify each of its 3-cylinder GT bikes for the North America market: 380 for Sebring, 550 for Indy, 750 for Le Mans.

Due to poor styling, high weight, poor ground clearance, a relatively low top speed and economical pricing the GT550 was more of a commuting and touring bike than a racer, despite its racetrack-derived name.[1]

Ram air system

The 550 (and the 380 ) have a ram-air cooling system for the one-piece cylinder head. Two-stroke engines lose power after the engine reaches its critical temperature, so Suzuki used a system from its 500 cc two stroke twin cylinder racer, the T500.[2]

This system consisted of a two piece aluminum shroud bolted to the cylinder head to duct ambient air over the cylinder head finning. The centre part of the head had an increased fin area and a larger shroud entry area in an effort to keep the centre cylinder running at the same temperature as the naturally more exposed outboard cylinders.[3]

Visible emissions control

SRIS Schematic. Note flow directional arrows

Suzuki Recycle Injection System (SRIS) was the first attempt by anyone to reduce visible emissions from a two stroke motorcycle. It was a small check valve in the bottom of each crank chamber. Two stroke engines have a tendency to collect unburnt oil and fuel in the bottom of the crank chamber at idle. Upon acceleration, after a period of idling, the unburned oil and fuel gets sucked up the transfer ports and contributes to an overrich mixture for the first 5 to 10 seconds resulting in a smokescreen from the exhaust. The SRIS plumbing routed the unburned fuel and oil to the next cylinder in the firing order thus allowing it to mix more thoroughly with the incoming charge of that cylinder and lowering the production of visible smoke. Overall fuel and oil consumption was unchanged but visible smoke was greatly reduced on sudden acceleration from rest.[4]

Exhaust system

The exhaust itself was unusual for the time in that the centre exhaust header was split in two and exited into two mufflers much smaller than the single mufflers supplied for the two outboard cylinders. This gave a bike a balanced look with two mufflers per side. The header pipes were all joined via balance tubes, known as Exhaust Coupler Tube System (ECTS), to increase low end torque. This exhaust was continued through to the end of production for the North American market but was dropped from the M model onwards in some other markets.

Automatic oil/fuel mixing

Suzuki began using automatic lubrication in 1966 to eliminate premixing of oil and fuel as had been the norm for all two strokes up until then. This system was launched to eliminate mixtures with far too much oil due to the operator's unnecessary effort to preclude engine seizures. The 550 had the latest version of this multipoint oil injection called Crankcase Cylinder Injection (CCI).

Undersquare engine

The 550 was considered by some to be well suited as a touring motorcycle with its long wheelbase and unstressed torquey engine. The engine will pull quite easily from ~3,500 RPM. The smaller bore/longer stroke dimensions allow quick burning of the air fuel mixture, allowing the use of regular grade fuel. This type of undersquare engine configuration has long since been discarded for use in street bikes by most Japanese motorcycle engine designers due to its inherent limitations on power increases and the recent advances in combustion chamber design allowing the use of large bore cylinders and high compression without detonation issues.

Specifications

Nippon Denso = 28A @ 6000 RPM
Kokusan = 15.5 A @ 6000 RPM
Single caliper hydraulic disc (subsequent MY)

Model year changes

1972 J model

The GT550 introductory model was Suzuki's counter to Kawasaki H1 Mach III. The GT550 had a massive four leading shoe double panel drum front brake shared with the GT750. The conventional telescopic front forks had rubber gaiters covering the fork stanchions. Both fenders were chromed steel. Chrome and polished aluminum were used on the rest of the bike. The fuel cap was, unusually for the times, lockable and this was carried on through to the end of production. The rear turn signal lenses were red. Engine cooling was by the Ram Air system. First year sales were 11,000+ units.[7]

1973 K model

A single hydraulically operated front disc brake was added in 1973. Otherwise the bike was the same as the previous model.

Both the wheel and the other fork leg were capable of accepting another disc and caliper and a switch to a twin-disc front brake (like the GT750) was not an uncommon modification some owners made (although the larger master cylinder from the 750 was required). The single disc arrangement continued throughout the rest of the GT550's production.

The brake light operated only by the rear brake in the UK market. A switch was available as a spare part to fit onto the front brake master cylinder casting which would also operate the brake light. The necessary wiring was already included on the main wiring harness in the headlamp shell. Sales were 14,000+ in 1973.[7]

1974 L model

Te rubber-gaiters were replaced by a cleaned up "Ceriani-style" set of forks. A touted benefit was better engine cooling but, with ram air, this was a non-issue for the most part. The three separate carburetors were replaced by three unitized rack mounted carburetors with a push-pull cable arrangement. The benefits of this were less costly carburetor balancing and more accurate fuel metering. The handlebar mounted cable operated choke was gone, replaced by a lever mounted directly on the rack of carbs. The cylinder head and the ram air shroud were redesigned to cater for this new carb setup.

A new airbox and filter assembly had bright chrome end caps and filter servicing was easier. The frame side covers were all new as well to blend in with the lines of the airbox end caps. The chain guard was chromed steel instead of black plastic, a marked improvement.

The instrument cluster still contained the speedometer and tachometer but a single digit LED gear indicator was added. This was a first for the motorcycle industry. It was in the centre of the instrument panel showing gear numbers 1 through 5 in a bright red colour. The neutral light indicator was retained as a separate item. Sales were 10,000+.[7]

1975 M model

In 1975, the internal parts of the fork were changed. The Exhaust Coupler Tube System (ECTS) link between the exhaust pipes disappeared in some markets outside of North America. The North America area kept the exhaust coupler tubes through to the end of production. This MY sales were 14,000+.[7]

1976 A model

1976 GT550A. The ram air cooling shroud is on top of the cylinder head.

In 1976 the front mudguard stay was removed. The rear shock was stiffened. The gear indicator changed to led segments rather than the previous dot matrix. An electric starter modification was included. This MY sales were 9,000+.[7]

1977 B model

The faces of the speedometer and tachometer were changed from a blue background to brown to match the appearance of the instruments on the GS models. There was also a change in the plastic used as lens because it no longer developed serious opacity and cracks after long exposure to sunlight. The instruments did not get the then-unique rose coloured back-lighting that the GS models had. The front brake caliper was changed to a pivoting unit made by Asco rather than the fixed Tokico caliper that had been supplied from the introduction of the disc brake system. The GT and GS series were sold side by side during this one year overlap. This was the last MY for GT550 production. This MY sales were ~6,000+ making this the rarest of all the 550 models.[7]

References

  1. 1 2 3 Siegal, Margie (November–December 2011). "1975 Suzuki GT550 Indy". Motorcycle Classics. Retrieved 23 April 2013.
  2. ↑ Cycle World, Vol. 11, No. 6, pg. 57
  3. ↑ GT550 Owner's Manual Suzuki Part #99011-34611
  4. ↑ Suzuki GT750 Service Manual Part #SR-3100 dtd. 07/72
  5. ↑ GT550 Owner's Manual Suzuki Part #99011-34611
  6. ↑ GT550 Service Manual, 2nd ed.
  7. 1 2 3 4 5 6 U.S. Suzuki Service Publication #3 dtd. 03/25/94
This article is issued from Wikipedia - version of the 6/24/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.