Solar-assisted heat pump

Hybrid photovoltaic-thermal solar panels of a SAHP in an experimental installation at Department of Energy at Polytechnic of Milan

A solar-assisted heat pump (SAHP) is a machine that represents the integration of a heat pump and thermal solar panels in a single integrated system. Typically these two technologies are used separately (or only placing them in parallel) to produce hot water.[1] In this system the solar thermal panel performs the function of the low temperature heat source and the heat produced is used to feed the heat pump's evaporator.[2] The goal of this system is to get high COP and then produce energy in a more efficient and less expensive way.

It is possible to use any type of solar thermal panel (sheet and tubes, roll-bond, heat pipe, thermal plates) or hybrid (mono/polycrystalline, thin film) in combination with the heat pump. The use of a hybrid panel is preferable because it allows to cover a part of the electricity demand of the heat pump and reduce the power consumption and consequently the variable costs of the system.

Optimization

The operating conditions' optimization of this system is the main problem, because there are two opposing trends of the performance of the two sub-systems: by way of example, a decreasing of the evaporation temperature of the working fluid generates an increasing of the thermal efficiency of the solar panel but a decreasing in the performance of the heat pump, with a decreasing in the COP.[3] The target for the optimization is normally the minimization of the electrical consumption of the heat pump, or primary energy required by an auxiliary boiler which supplies the load not covered by renewable source.

Configurations

There are two possible configurations of this system, which are distinguished by the presence or not of an intermediate fluid that transports the heat from the panel to the heat pump. Machines called indirect- expansion mainly use water as a heat transfer fluid, mixed with an antifreeze fluid (usually glycol) to avoid ice formation phenomena during winter period. The machines called direct-expansion put in the refrigerant fluid directly inside the hydraulic circuit of the thermal panel, where the phase transition tooks place.[3] This second configuration, even though it is more complex from the technical point of view, allows to obtain several advantages:[4][5]

Comparison

Generally speaking the use of this integrated system is an efficient way to employ the heat produced by the thermal panels in winter period, which wouldn't be normally exploited because of its too low temperature.[2]

Separated production systems

In comparison with only heat pump utilization, it is possible to reduce the amount of electrical energy consumed by the machine during the weather evolution from winter season to the spring, and then finally only use thermal solar panels to produce all the heat demand required (only in case of indirect-expansion machine), thus saving on variable costs.[1]

In comparison with a system with only thermal panels, it is possible to supply to a greater part of the winter heating required using a non-fossil energy source.[6]

Traditional heat pumps

Compared to geothermal heat pumps, the main advantage is that the installation of a piping field in the soil is not required, which results in a lower cost of investment (in the investment cost of a geothermal heat pump system about 50% is given by drilling costs) and in more flexibility of machine installation, even in areas in which there is poor space availability. Furthermore, there are no risks related to possible thermal soil impoverishment.[7] A disadvantage, similarly to as occurs for air heat pumps, solar-assisted heat pump performances are affected by atmospheric conditions.

Compared to air heat pumps, as already mentioned, there are variations less significant of the performances (linked to the variation of solar radiation and not to air temperature oscillation). This produces a greater SCOP (Seasonal COP). In addition to this, the evaporation temperature of the working fluid is higher than the case for air, so in general the coefficient of performance is significantly higher.[4]

Low temperature conditions

In general, a heat pump can evaporate at temperatures below the ambient temperature. In a solar-assisted heat pump this generates a temperature distribution of the thermal panels below that temperature. In this condition thermal losses of the panels towards the environment become additional available energy to the heat pump.[8][9] In this case it is possible that the thermal efficiency of solar panels is more than 100%.

Another free-contribution in these conditions of low temperature is related to the possibility of condensation of water vapor on the surface of the panels, which provides additional heat to the heat transfer fluid (normally it is a small part of the total heat collected by solar panels), that is equal to the latent heat of condensation.

Heat pump with double cold sources

The simple configuration of solar-assisted heat pump as only solar panels as heat source for the evaporator. It can also exist a configuration with an additional heat source.[1] The goal is to have further advantages in energy saving but, in the other hand, the management and optimization of the system become more complex.

The geothermal-solar configuration allows to reduce the size of the piping field (and reduce the investment) and to have a regeneration of the ground during summer through the heat collected from the thermal panels.

The air-solar structure allows to have an acceptable heat input also during cloudy days, maintaining the compactness of the system and the easiness to install it.

See also

References

  1. 1 2 3 "Solar-assisted heat pumps". Retrieved 21 June 2016.
  2. 1 2 "Pompe di calore elio-assistite" (in Italian). Retrieved 21 June 2016.
  3. 1 2 Nicola Fallini; Stefano Luigi Floreano (31 March 2011). "Sistemi a pompa di calore elioassistita: modello di simulazione in ambiente TRNSYS e confronto energetico di configurazioni impiantistiche" (PDF) (in Italian). Retrieved 21 June 2016.
  4. 1 2 Jie, Jia; Hanfeng, Hea; Tin-tai, Chowb; Gang, Peia; Wei, Hea; Keliang, Liua (2009). "Distributed dynamic modeling and experimental study of PV evaporator in a PV/T solar-assisted heat pump". International Journal of Heat and Mass Transfer. 52 (5-6): 1365–1373. doi:10.1016/j.ijheatmasstransfer.2008.08.017.
  5. ↑ Jie, Jia; Gang, Peia; Tin-tai, Chowb; Keliang, Liua; Hanfeng, Hea; Jianping, Lua; Chongwei, Hana (2007). "Experimental study of photovoltaic solar assisted heat pump system". Solar Energy. 82 (1): 43–52. doi:10.1016/j.solener.2007.04.006.
  6. ↑ Kuang, Y.H.; Wang, R.Z. (2006). "Performance of a multi-functional direct-expansion solar assisted heat pump system". Solar Energy. 80 (7): 795–803. doi:10.1016/j.solener.2005.06.003.
  7. ↑ Carotti, Attilio (2014). WOLTERS KLUWER ITALIA, ed. Edifici a elevate prestazioni energetiche e acustiche. Energy management (in Italian).
  8. ↑ Huang, B.J.; Chyng, J.P. (2001). "Performance characteristics of integral type solar-assisted heat pump". Solar Energy. 71 (6): 403–414. doi:10.1016/S0038-092X(01)00076-7.
  9. ↑ "Thermboil - Pannelli termodinamici" (in Italian). Retrieved 21 June 2016.
Wikimedia Commons has media related to Heat pumps.
This article is issued from Wikipedia - version of the 6/22/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.