GWR 4300 Class

Great Western Railway 4300 Class

Type and origin
Power type Steam
Builder
Build date 1911–1932
Total produced 342
Specifications
Configuration 2-6-0
UIC class 1'C h
Gauge 4 ft 8 1⁄2 in (1,435 mm) standard gauge
Leading dia. 3 ft 2 in (0.965 m)
Driver dia. 5 ft 8 in (1.727 m)
Minimum curve 6 chains (400 ft; 120 m) normal,
5 chains (330 ft; 100 m) slow
Length 58 ft 1 1⁄4 in (17.71 m)
Width 8 ft 11 in (2.718 m)
Height 13 ft 0 in (3.962 m)
Axle load 17.60 long tons (17.88 t; 19.71 short tons)
Adhesive weight 52 long tons 0 cwt (116,500 lb or 52.8 t)
(52.8 t; 58.2 short tons)
Loco weight 62 long tons 0 cwt (138,900 lb or 63 t)
(63.0 t; 69.4 short tons)
Tender weight 40 long tons 0 cwt (89,600 lb or 40.6 t)
(40.6 t; 44.8 short tons)
Fuel capacity 7 long tons 0 cwt (15,700 lb or 7.1 t)
(7.1 t; 7.8 short tons)
Water cap 3,500 imp gal (16,000 l; 4,200 US gal)
Firebox:
 • Firegrate area		 20.56 sq ft (1.910 m2)
Boiler pressure 200 psi (1.38 MPa)
Heating surface:
 • Tubes		 1,349.64 sq ft (125.386 m2)
 • Firebox 128.72 sq ft (11.958 m2)
Superheater:
 ​
 • Heating area 191.88 sq ft (17.826 m2)
Cylinders Two, outside
Cylinder size 18.5 in × 30 in (470 mm × 762 mm)
Performance figures
Tractive effort 25,670 lbf (114.19 kN)
Career
Operators Great Western Railway,
British Railways
Power class GWR: D; BR: 4MT
Numbers 4300–4399, 5300–5399, 6300–6399, 7300–7321, 9300–9319
Axle load class GWR: 4300–7300s Blue; 8300–9300s: Red
Locale Great Britain
First run 1911
Withdrawn 1936–1964
Disposition Two preserved, remainder scrapped

The Great Western Railway (GWR) 4300 Class is a class of 2-6-0 (mogul) steam locomotives, designed by G.J. Churchward for mixed traffic duties. Three hundred and forty two examples were built from 1911-1932.

Background

In 1906 Churchward fitted a more powerful Standard No. 4 boiler to his successful 3100 Class 2-6-2T to create the GWR 3150 Class. These showed themselves to be successful locomotives but their 65 long tons 0 cwt (145,600 lb or 66 t) weight and 2,000 imp gal (9,100 l; 2,400 US gal) water capacity meant that they tended to be restricted to suburban passenger traffic. Churchward was looking forward to the replacement of various of his predecessor’s 4-4-0 classes on secondary duties. In 1911 he therefore designed a tender version of the 3150 class which would be suitable for a wide range of intermediate duties. [1]

Design

The class was ‘a total synthesis of standard parts, using the outside cylinders of the Saint, the wheels of ’31XX’ 2-6-2 tank and the No.4 boiler, in its superheated form.’[2] No prototype was required as the fundamental design had proved itself.

Production series

The locomotives quickly proved themselves to be so useful that they were produced more or less continuously in a series of batches (or lots) over a twelve year period (1911-1923), sometimes incorporating detailed differences. Two further lots were built in 1925 and 1932 by Churchward's successor, Charles Collett.[3]

Lot 183

The first twenty examples, numbered 4301-20, were delivered by Swindon Works between June and October 1911. These had inside steam pipes, and were among the first GWR locomotives to be fitted with top feed apparatus.[4] Nos. 4311–20 had boilers designed to operate at 225 psi (1.55 MPa) pressure but only 4315 and possibly 4316 ever worked at that pressure.[5]

Lots 193, 194 and 198

Three further batches, totalling a further forty locomotives (4321-4360) were built at Swindon and delivered June 1913 and May 1914, before the onset of the First World War impeded further production. These locomotives (and all subsequent examples had frames lengthened by 9 in (229 mm) at the rear to give better access for maintenance as well as providing more room in the cab.

Lots 202 and 204-208

The class proved to be ‘just the type that was needed during the 1914-18 war and were accordingly built in considerable numbers during that period.’[6] Six batches, totalling one hundred locomotives (numbered 4361-4399, 4300, 5300-5359) were built between May 1915 and September 1918, and a further ten (5360-5369) between January and June 1919. From 1917 detailed changes were made to the design giving better weight distribution between the wheels which were later applied to other members of the class[7] Eleven examples of the class were transported to France during World War I in the service of the Railway Operating Division of the British Army and these were 5319 - 5326 and 5328 - 5330. One survives in preservation.

Lots 209, 211-212, 216, 230

The first three of these lots were for seventy locomotives built between June 1919 and July 1921 (Nos. 5370-99 and 6300-6341). Lot 216 was for a further 28 locomotives (6342-6369) but Swindon works was then unable to keep pace with the demand for them and only the first twenty were completed after delay, between March and December 1923. The remainder (6362-9 and 7320/1) were later built under lot 230 in 1925.[8] 6320 was converted to oil firing between 1947 and the equipment was removed in 1949.

Lots 218 and 222

As Swindon works could not keep pace and order was placed with Robert Stephenson and Company in 1921 for fifty locomotives (Nos. 6370-99 and 7300-7319). The first 35 of these (Lot 218) were built by the company between April 1921 and January 1922. The remaining fifteen were built at Swindon from parts manufactured by RSH between November 1921 and January 1922. In 1925 Nos. 7300–7304 were modified for better balance and had detail alterations.

Lot 276

In 1932, Collett built a further twenty examples (9300 – 9319) to a modified design with side window cabs, outside steam pipes and a screw reverse. He also extended the frames, increasing the weight to 65 long tons 0 cwt (145,600 lb or 66 t) (72.8 short tons), which placed them in the Red band of route availability. After passing into British Railways ownership, these locomotives were modified back to light buffer beam design and were renumbered 7322–7341 between 1956 and 1959.

8300 Class

No. 5327 at Swindon 11 June 1950 (modified to the heavier version as No. 8327 1928-1944).

The class were widely used in Devon and Cornwall where the track had many sharp curves. It was found that flange wear on the leading driving wheels became excessive as a result of these bends. In November and December 1927 additional weight was added to the front end of four examples so that the pony truck would be forced to impart more side thrust to the main frames on bends. These locomotives reverted to their original state, but between January and March 1928, 65 engines of 5300 series received additional weight on the pony truck, and 3000 was added to their running numbers, temporarily creating an ‘8300 Class’. However, the additional weight placed them in the Red category of route availability. From 1944 onwards there was a shortage of locomotives in the Blue category and so the additional weights were removed and the surviving locomotives resumed their original running numbers. The last to be returned to its original condition was 8393 in September 1948.[9]

Use

The 4300 Moguls were the maids of all work on the GWR network and later the Western Region of British Railways. Employing a Standard number 4 boiler and the support struts similar to those fitted to the '2800' class, the class very quickly earned an excellent reputation in its ability to handle most types of traffic, from local stopping goods to main line expresses. According to O.S. Nock they "could handle the heavy goods work as well as the 'Aberdares' and could run up to 70 mph with passenger trains, in other words they were the ideal mixed traffic locomotive".[10]

Withdrawal

Although the class continued to be very useful and the final batch were still relatively new, 100 of the earlier examples were withdrawn between 1936 and 1939 and the wheels and motion of eighty were used for the Grange Class and twenty for Manor Class engines. It was intended to replace the whole class in this way but the advent of the Second World War in 1939 brought a temporary halt to withdrawals and the programme was never revived.[11] Further withdrawals resumed in 1948 under British Railways ownership, but the last six examples survived until 1964.

5322 preserved in WWI Railway Operating Division khaki livery

Accidents and incidents

Preservation

Only two examples have survived to preservation:

Number Built Withdrawn Location Current status Notes
5322 (ex-8322) Aug 1917 (Swindon Works) Apr 1964 Didcot Railway Centre On static display One of 11 locos exported to France in World War I.

Painted in British Railways black with early crest.

Withdrawn in Summer 2014 with boiler problems.

7325 (ex-9303) Feb 1932 {Swindon Works) Apr 1964 Severn Valley Railway On static display Future overhaul possible with return to original condition

5322 is the older of the two as it was built in 1917, during the Great War, at Swindon Works. It was sent, with several other members of the class, to France for hauling munitions and hospital trains. There it was painted in War Department livery and given the number ROD5322. Demobbed in 1919 at Chester it returned to the GWR fleet until it was withdrawn from service in April 1964. It was sent to Woodham Brothers scrapyard in Barry, South Wales. The first Barry locomotive to be subject to a preservation fund, it was the second locomotive to leave Woodham's. 5322 thus ended up as the sole early 43xx to be preserved. It had previously been restored to working order but was not steamed after 1975 until returning to steam in 2008 at the Didcot Railway Centre, restored to its 1919 War Department condition.

9303 is one of the final batch of 342 locomotives built between 1911 and 1932. They were built with larger cabs and had a weight attached to the buffer beam to place more weight on the leading pony wheels. This was done to reduce the wear on the leading driving wheels. In 1958 the weight was removed from the buffer beam to give the locomotive more route availability. At the same time it was renumbered 7325. The plan is to replace the missing weight at the next overhaul so it can run as 9303.

7325 has also run on the mainline in preservation.

References

  1. ↑ Nock, O. S. (1983). British Locomotives of the 20th Century Vol.1. London: Book Club Associates. p. 169.
  2. ↑ Nock (1983 p.169
  3. ↑ Production details from Le Fleming, H.M. (1962). The Locomotives of the Great Western Railway, part nine: Standard two-cylinder Classes. Kenilworth: RCTS. pp. J24–5. ISBN 0901115371.
  4. ↑ Le Fleming (1962), pp. J5 and J13.
  5. ↑ Le Fleming (1962), pp. J5 and J13.
  6. ↑ Le Fleming (1962), p. J13.
  7. ↑ Le Fleming (1962), p. J13.
  8. ↑ Le Fleming (1962), p. J13.
  9. ↑ Le Fleming (1962), p. J14.
  10. ↑ Nock (1983 p.169
  11. ↑ Le Fleming (1962), p. J14.
  12. ↑ Gerard, Malcolm; Hamilton, J. A. B. (1981) [1967]. Trains to Nowhere. London: George Allen & Unwin. pp. 45–49. ISBN 0-04-385084-7.
  13. ↑ Trevena, Arthur (1980). Trains in Trouble. Vol. 1. Redruth: Atlantic Books. p. 40. ISBN 0-906899-01-X.
  14. ↑ Vaughan, Adrian (1989). Obstruction Danger. Wellingborough: Patrick Stephens Limited. pp. 80–88. ISBN 1-85260-055-1.
  15. ↑ Earnshaw, Alan (1993). Trains in Trouble: Vol. 8. Penryn: Atlantic Books. p. 25. ISBN 0-906899-52-4.
  16. ↑ Hall, Stanley (1990). The Railway Detectives. London: Ian Allan. p. 119. ISBN 0 7110 1929 0.
Sources
Wikimedia Commons has media related to GWR 4300 Class.
This article is issued from Wikipedia - version of the 7/26/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.